| |
Items written in gold are exchange items. Click here for essential information.
|
|
 |
Product No - FKSR1600
SR20/1600 Fitting Kit
Reversed engine x-member , modified SR steel engine mounts, Modified steering draglink, plus custom gearbox x-member & 24mm sway bar with bushes, saddles & link ends. Only cutting required is for the gear stick through the floor. |
$930
|
 |
Product No - FKFJ1600
FJ20/1600 Fitting Kit
Reversed engine x-member, custom engine mounts & gearbox x-member. 24mm adjustable sway bar with bushes, saddles & link ends. |
$830
|
 |
Product No - FKCA1600
CA18/1600 Fitting Kit
Engine x-member, custom engine mounts & gearbox x-member.
24mm adjustable sway bar with bushes & saddles.(Revision 2)
|
$830
|
 |
Product No - FK13B1600
13BT/1600 Fitting Kit
Reversed & scalloped engine x-member, mounts removed. Custom engine support bar (weld in), with new rubber engine mounts. Custom gearbox x-member (2 piece) with new rubber mount.
24mm adjustable sway bar with link ends, bushes & saddles.
Trans tunnel cover (weld in). |
$1200
|
 |
Product
No - LOOM
Plug & Play Wiring Loom
Send us your loom and we'll send it back ready to plug straight in to avoid spending up to $2K on auto electrical fees. The looms have all the redundant wiring removed and modified with unique connectors leaving no confusion about what goes where. Comes with instructions.
Available for standard ECU only. Send us just the engine harness if you want just the engine/EFI side back. Or the engine and complete under-dash harness if you want all electrical incl lights etc.
Please mail us with exactly what you want and we'll tell you further details about what you need to send back. Tell us also if have a half-cut and want to use the newer instrument cluster. There is no exchange surcharge on this item because we will not send one without your loom first. Don't forget to tell us Car, Engine and your Location. |
From
$550
to
$850 |
|
Product
No - REM1600
Rubber Engine Mount (pair)
Standard 1600 replacement part . Original mounts are needed with all conversions. You might like to replace yours if they are looking a bit worse for wear. |
$140 |
 |
Product
No - RFE1600
Rebuilt Front End
Datsun 1600 rebuilt front end kit. Includes
powdercoated control arms, radius rods &
steering knuckles as well
as new balljoints & tie rod ends. Urethane
control arm & radius rod bushes supplied. |
$390 |
|
Product
No - BK1600
New Bush Kit Suit 1600
Front Lower Control Arm - Inner $42
Front Idler Arm $37
Front Strut Bar to Chassis Mount $40
Front Sway Bar Link Bush Kit $18
Front Sway Bar Mount to Chassis $21
Rear Control Arm Inner $78
Rear X-Member to Chassis Mount $119
Rear Diff Mount $62
Rear Shock Lower $15
Rear Shock Upper $16
(note minimum freight charge is $8.00) |
$410 |
 |
Product No - SWB1600
1600 Conversion Sway Bar Kit
Adjustable 24mm swaybar with D-bushes,saddles & link ends. Will also fit around 'Trust' and 'Greddy' style oil pan. |
$280 |
 |
Product
No - URCP
Ultimate Race Coilover Package
Shortened 200B or Stanza struts (cut and re-threaded, not welded), KYB inserts, Adjustable Coilover Kit fitted with 65mm, 250lb King springs. Billet aluminium adjustable camber top. Re-built Front End Required. Click for more info
Can also use 1600 struts.
Upgrade to Thrust Bearing $70 (see below for more info)
Upgrade to Adjustable Koni Shocks add $380
|
$1495
|
 |
Product No - ACT001
Adjustable Camber Top (pair)
Designed and manufactured by Mad Dat, these adjustable camber tops are CNC machined from billet aluminium featuring stainless steel fasteners, German quality pillow ball and anodised black. Will suit most 65mm coilover setups.
|
$490 |
 |
Product No - CTTHB
Upgrade to URCP Thrust Bearing
The unique thrust bearing is utilised to take care of steering rotation rather than relying on the pillow ball to swivel and rotate, therefore making steering lighter and more responsive as well as extending the life of the pillow ball. Purchase with ACT001 or URCP only. |
$70 |
 |
Product
No - FBK001
Front
Brake Conversion Kit
Includes 280mm vented disc rotors, RX7 S4
Calipers
(new seal kits fitted), adaptor brackets, bolts, washers. wheel bearing kits, new rubber lines. Kit is designed to fit 200B or late Stanza struts. Will not affect wheel off-set. Comes wtih engineers report. Option of red or black calipers.
See the brakes section for more options.
Slotted Rotors and RDA approved braided lines add $145
Slotted & Dimpled Rotors and RDA approved braided lines add $250 |
$1265 |
|
Product
No - SHA1600RK
Koni Adjustable Rear Shocks
(pair)
Suit 1600 |
$360 |
|
Product
No - SP038
690lb Rear Lowered King Springs
(pair)
Suit 1600 |
$155 |
 |
Product
No - RRCA1600
Rebuilt Rear Control Arms
(1600)
Rear arms are stripped bare, powdercoated
black finish, new bearings fitted.Hub fittings
zinc plated finish. Exchange item. |
$490 |
 |
Product
No - ARXM1600
Adjustable Rear X-Member
X-member is stripped & fitted with new
adjustable pickup points. Exhaust hole is
enlarged to 100mm. Powdercoated black finish
& supplied with adjustable pins (camber
& toe are adjustable).Suitable for R200 diff conversion. |
$550 |
 |
Product
No - RXM1600
Rear X-Member Large Exhaust Hole
Cross Member is powdercoated, willl fit a 3" exhaust. (exchange item) |
$175 |
 |
Product
No - DBR200
R200 Diff Bracket Kit
Allows easy fitment of long nose R200 diff's
into the Datsun 1600 rear x-member. Manufactured
from 40 x 10mm plate steel & supplied
with urethane bushes & replacement bolts/washers. |
$195 |
 |
Product
No - DAKR200
R200 Diff Axel Kit
Buy your own diff minus axels and add this kit for an instant bolt-in with no mods required to 1600 and 180B. Uses all new parts, kit consists of new replaceable CV joints, hardened chrome molly axels, diff output shafts, hub adaptor plates and all nuts, bolts and washers required. Comes with fitting instructions. Suitable for approx 400+ kw.
|
$1900
|
 |
Product
No - RBK
Rear
Brake Conversion Kit
Includes rotors, rebuilt calipers, brackets,
hoses and lines and handbrake cable set. Will
fit Datsun 1600/180B.
Comes with engineers report. |
$1125 |
 |
Product
No - MD024
R31/1600
Handbrake Cables
Handbrake cables as per MD018 kit. |
$240 |
 |
Product
No - RBB1600
R31/1600
Caliper Brackets
Conversion brackets to fit R31 brakes to your
Datsun 1600/180B. |
$160 |
 |
Product
No - BBK1600
1600
Brake Booster/Master
Datsun 180B small can booster. Gives easy braking while leaving more room in the engine bay. Powdercoated and reconditioned with all
new internals and fitted with 7/8th master
cylinder. Polished alloy brackets supplied. Suitable for large caliper disc brake upgrades (front and rear). Other cylinder sizes available on request. |
$420 |
 |
Product
No - ACK1600
1600 Adjustable Front
Arms
Remanufactured front control arms for your
race or rally 1600/510.TIG welded & built to a high standard for motorsport use to increase/decrease bottom-end camber. Scope for plenty of adjustment. Powdercoated with new polyurethane bushes. |
$350
|
 |
Product
No - HBL
Hard Brake Lines incl Bias Valve
Info to come |
$499 |
 |
Product No - ACK1600
Caster Adjuster Bar Kit (1600)
Suit 1600 and 180B. These are machined from high-quality steel and heat-treated after forging to ensure that these are much stronger than original. Supplied with polyurethane bushes and finished in hard black enamel. Plenty of room for adjustment. |
$220
|
 |
Product
No - SBB1600
1600 Steering Box Brace
Reduce the steering flex & "tram
tracking" in your 1600. The cheapest
performance improvement you can make ! Stainless steel
construction & hi tensile 304 grade stainless bolts supplied. Also available in LHD |
$85 |
 |
Product
No - BSS1600
1600 Bump Steer
Spacers (new design)
Reduce the bump steer on your lowered Datto
with the fitment of these. Fits between bottom
of strut & steering knuckle, hi tensile
bolts & washers supplied. Required to improve performance after lowering your datto if your LCA's are either horizontal or pointing up. They should droop. |
$118 |
 |
Product
No - MD076
1600 Tie-Rod/Balljoint
Kit
New tie-rods (4) & balljoints for Datsun
1600. 2 year/40,000km warranty. |
$168 |
 |
Product
No - EXTSR1600
SR20/1600 Extractors
Custom made to suit fitment of SR20 atmo motor
using our fitting kit.
1 5/8 primaries, 2 inch secondaries into 2
1/2 outlet. Finished in black hi temp paint
(photo shows set finished in ceramic coating
- $190.00
extra cost). |
$450 |
 |
Product
No - EXTFJ1600
FJ20/1600 Extractors
Custom made to suit fitment of FJ20 motor
using our fitting kit.
1 5/8 primaries, 2 inch secondaries into 2 1/2 outlet. Finished in black hi temp paint. |
$450 |
 |
Product
No - ACCA1600
FJ/CA/SR/1600 Accelerator
Cable |
$85 |
 |
Product
No - MD011
SR20/1600
Modified Draglink
Draglink is modified (bending forward to allow clearance
on the alloy
SR sump) Comes with engineers report (legal in all
Australian states) RHD but we can modify LHD draglinks
if supplied by the customer. |
$195 |
 |
Product
No - EXM1600
1600
Reversed Engine X-Member
Cross member has reversed control arm locator pin holes, finished
in durable satin black powder coat finish. |
$195 |
 |
Product
No - EMSR1600
SR20/1600
Engine Mount Set
(pair)
Modified SR steel engine mount brackets, new base
plates fitted, finished in satin black powder coat.
Exchange items.
Bolts & washers supplied. |
$160 |
 |
Product
No - EMFJ1600
FJ20/1600
Engine Mount Set
(pair)
Custom steel engine mount brackets (pair).
These are custom made & finished in satin
black powder coat. Bolts & washers supplied. |
$160 |
 |
Product
No - EMCA1600
CA18/1600
Engine Mount Set
(pair)
Custom steel engine mount brackets (pair). These
are custom made & finished in satin black powder
coat. Bolts & washers supplied. |
$160 |
 |
Product
No - GXMSR1600
SR20/1600
Gearbox X-Member
Custom gearbox x-member. Winged design to
allow for optimum exhaust clearance without
sacrificing ground clearance.
Finished in satin black powder coat. |
$155 |
 |
Product
No - GXMFJ1600
FJ20/1600
Gearbox X-Member
Custom gearbox x-member featuring winged design
for optimum exhaust clearance without sacrificing
ground clearance.
Finished in satin black powder coat. |
$155 |
|
BACK
TO TOP
